Pressure sensitive vinyl decal products were introduced to the auto industry about 30 years ago. Those old vinyl decals were calendered, thick and difficult to work with. Most all applications were done dry, with poor results. Some manufacturers advised soap and water applications. Often the substrate was cleaned with a shop rag that had been exposed to numerous varieties of solvents.

Cleaning with oil-based solvents, using cloth towels or commercial paper towels just added to the contamination problem and prohibited good bonding. Soapy water generates foam, so bubbles were easily trapped under the vinyl. If that wasn't enough, the soap and water mixed with contaminating solvent residues and would take hours to bond. Obviously no one was thrilled about applying vinyl in those days.

Well, times have changed and so have vinyl films! We now have a large variety of "high performance cast" films from which to choose. When matched to the correct choice of transfer, i.e. application tapes (Low Tac, Mid Tac, High Tac), and stored properly (tapes gain tac as they age) out of the air and away from sunlight, today's films will perform much better than those products of the past.

RAPID TAC AND RAPID TAC II:
Application Fluid

For fast, easy, quality wet applications with no bubbles even in cold weather

Granted, not all vinyl and graphic applications need to be a wet application to be successful, but we do know that in most applications nearly 50 percent in labor time can be saved by using a Rapid Tac application fluid. Sometimes a job normally requiring two people to perform a dry application can be done in less time by one person if using an application fluid like Rapid Tac or new Rapid Tac II. Application fluid cleans without leaving residues. Best of all it stimulates the adhesive to bond in approximately 90 seconds, even in a colder environment. It will not cause bubbles so there's no poking holes in your work. Your customers and your reputation will benefit from higher-quality applications and your production will increase as well.

The original Rapid Tac Application Fluid was formulated to make wet application of vinyl films simple and fast. Rapid Tac application fluid is the best choice when working with premium cast films and most acrylic adhesive systems. Applying vinyl wet with Rapid Tac gives you control over positioning time while you "float" the film. Rapid Tac and Rapid Tac II also increase the adhesive bond between your film and the substrate and will eliminate air bubbles. Another benefit to applying vinyl wet is the ease of removing the transfer film. Simply spray the transfer film with Rapid Tac to make it easier to pull away the transfer tape. Soap and water simply can't compare.

Rapid Tac II helps most adhesives to bond faster than the original Rapid Tac. It is formulated for intermediate calendered and ultra calendered films that don't normally have an adhesive as aggressive as cast premium films. Rapid Tac II is also perfect for cold weather and glass applications.

Click here to see how Rapid Tac and Rapid Tac II work

RAPID PREP:
Wax, Silicone and Grease Remover

A non-hazardous fluid for pre-cleaning substrates

Rapid Prep isn't just a wax remover. Rapid Prep is formulated to cut and clean almost any residue such as silicones, wax, oils or grease that could contaminate a paint or film application. Designed for cleaning or pre-cleaning, Rapid Prep is a non-hazardous wash solvent that removes wax, grease, oil and silicone. Use Rapid Prep to clean the substrate (sign panels, glass, painted surfaces on autos boats, aircraft, etc.) Rapid Prep is also non-flammable making it a superior product for sign shops, body shops and trim shops where safety is a priority. Rapid Prep is an extremely cost effective product designed by people just like you who need a better solution to ensure trouble free film and paint applications.

RAPID REMOVER:
Adhesive Remover

For removing adhesives quickly without damage or mess. The original Adhesive Remover.

How about saving some more labor hours? Rapid Remover is a guaranteed labor-saving product. To remove decals and vinyl from signs, windows, autos and many other substrates, many people are using lacquer thinner, MEK, acetone, paint stripper, grinders, etc., all of which are hazardous products. Experienced professionals start by using a heat lamp tree to soften vinyl. After peeling the vinyl off use Rapid Remover to easily remove the adhesive residue.

Rapid Remover is a non-toxic, water soluble adhesive remover that breaks down and removes most adhesives in 60 seconds!  Spray it on, wait 30 to 60 seconds and easily wipe it off with a plastic squeegee, all with no damage to painted or bare metal surfaces. What may have been a four hour job (and a messy one at that) can now be done in less than half that time. Get the right tool for the job

Home | Products | Distributors | Tech Tips | Featured Project | Endorsements | MSDS | Become a Distributor | Links
Contact Us | Rapid Tac Canada |

© 2006 Rapid Tac Inc. All rights reserved